Products

• 8 Binary Commands over IEEE C37.94 Optical link.
• Offers up to 8 independent Binary Command Input and 8 independent Binary Command Output channels which can
  be operated selectively; in a combination; or simultaneously over a IEEE C37.94 compliant optical fiber link.
• Command Transfer Time (including relay operating time) is <5ms.
• May be used independently in a point-to-point application between two nodes connected over an optical fiber link
• Also optionally available with 2 x IEEE C37.94 Optical Interfaces for optical link redundancy; or for use in 4+4
  point-to-multipoint applications

• 8 Binary Commands over E1, 2.048Mbps link
• Offers up to 8 independent Binary Command Input and 8 independent Binary Command Output channels which can
  be operated over an E1, 2.048Mbps, G.703 interface option for transmission over E1/SDH links.
• Command Transfer Time (including relay operating time) is <5ms
• May be used independently in a point-to-point application between two nodes connected over E1/SDH links
• Also optionally available with 2 x E1 Interfaces for E1 link redundancy; or for use in 4+4 point-to-multipoint applications

• 8 Binary Commands over E1 plus IEEE C37.94 Optical, 1+1 redundant transmission links with path protection / route protection with automatic failover
• Offers up 8 independent Binary Command Input and 8 independent Binary Command Output channels which can be operated selectively; or simultaneously; or in a combination over an E1 (2.048Mbps) plus IEEE C37.94 Optical (1+1 redundant transmission links) with link failure detection and automatic failover.
• Command Transfer Time (including relay operating time) is <5ms
• Network interface options:
• E1, 2.048Mbps interface
• IEEE C37.94 optical fiber interface
• 1+1 redundant path protection / route protection option
• E1, 2.048Mbps and IEEE C37.94 (1+1 redundant) interfaces.

• 8 Binary Commands over E1 plus E1, 1+1 redundant interfaces with path protection / route protection with automatic failover
• Offers up 8 independent Binary Command Input and 8 independent Binary Command Output channels which can be operated selectively; or simultaneously; or in a combination over an E1 (2.048Mbps) plus E1 (2.048Mbps) - 1+1 redundant transmission links with link failure detection and automatic failover.
• Command Transfer Time (including relay operating time) is <5ms

• 8 Binary Commands and IEC-61850 GOOSE over E1; plus IEEE C37.94; plus Ethernet (1+N redundant transmission) links
• 1+1 redundant protection switching / route protection is available between E1 interfaces / IEEE C37.94 optical / IP/Ethernet/MPLS with IEC 61850 GOOSE and automatic switchover to redundant link in the event of the failure of the primary link.
• Command transfer time for Binary and IEC-61850 GOOSE Interface over E1 / IEEE C37.94 / Ethernet / IP/MPLS / MPLS-TP is <5ms

• IEC 61850 GOOSE (PSCH1 and PSCH2) over IP/MPLS / MPLS-TP (10/100BaseT RJ45, or 100BaseFX Optical) Ethernet links
• Designed transport IEC-61850 GOOSE* (*Generic Object Oriented Substation Event) messages over an IP/MPLS network.
• 8 Binary Inputs / Outputs and performs GOOSE to Binary / Binary to GOOSE conversion functions, thereby allowing the users to install VCL-TP Teleprotection - IEC-61850 GOOSE over IP/MPLS equipment between sub-stations where one sub-station (protection relay) is using GOOSE messages and the corresponding, complementing sub-station (protection relay) at the other end is using binary commands.
• VCL-TP Teleprotection - IEC-61850 GOOSE over IP/MPLS incorporates the same level of “reliability” and “dependability” that the users have come to expect of the IEEE C37.94 based communication interface. Additionally, the VCL-TP Teleprotection - IEC-61850 GOOSE over IP/MPLS provides un-paralleled security, speed as well as all the advantages of an IEC-61850 GOOSE based system operating in a “Digital Sub-station” environment.
• Command Transfer Time (including relay operating time) is <5ms

• 8 Binary Commands over IP/MPLS / MPLS-TP (10/100BaseT RJ45, or 100BaseFX Optical) Ethernet transmission links
• VCL-TP, Teleprotection over IP / MPLS Equipment incorporates the same level of “reliability” and “dependability” that the users have come to expect of the IEEE C37.94 based communication interface. Additionally, the VCL-TP, Teleprotection over IP/MPLS Equipment provides un-paralleled security, speed as well as all the advantages of operating in a “Digital Sub-station” environment.
• Offers up 8 independent Binary Command Input and 8 independent Binary Command Output channels
• Available with:
• 10/100BaseT (Electrical) Interface to provide Teleprotection over IP/MPLS link.
• 100BaseFX (Optical) Ethernet Interface to provide Teleprotection over IP/MPLS link.

• VCL-2711 is a ruggedized, robust and sub-station-hardened transmission equipment which converts and transmits
  up to four IEEE C37.94 Interfaces over an Ethernet / IP/MPLS / MPLS-TP link with “SDH / SONET like” performance.
• End-to-end transmission delay (latency) of less than 6ms
• Symmetrical transmission latency with zero transmission errors
• SDH / SONET quality “Jitter” and “Wander” control
• Multiple, integrated clock synchronization options

• VCL-2709, IEEE C37.94 to E1 Converter is a ruggedized and robust, sub-station-hardened protocol converter that converts the IEEE C37.94 Interface to 2.048Mbps E1 Interface and vice-versa.
• Includes precise clock recovery and clock re-generation functions which allows the transmission of IEEE C37.94
  channels over an E1/SDH network for error free transmission.
• Number of IEEE C37.94 interfaces per card: 1
• Number of interfaces: 1, E1 (2.048 Mbit/s) Interface (Electrical G.703)

• VCL-6045 is a ruggedized and robust, sub-station-hardened protocol converter that converts up to 4 x IEEE C37.94 Interfaces to 4 x 2.048Mbps E1 and vice-versa.
• Supports point-to-point as well as point-to-multipoint applications.
• Includes precise clock recovery and clock re-generation functions which allows the transmission of IEEE C37.94 channels over an E1/SDH network for error free transmission.
• Number of IEEE C37.94 interfaces per card: 4
• Number of interfaces: 4, E1 (2.048 Mbit/s) Interface (Electrical G.703)

• VCL-2710 is a ruggedized, sub-station-hardened converter that converts an IEEE C37.94 Multi-Mode to Single-Mode Optical signal.
• The equipment is designed to convert and propagate IEEE C37.94 multi-mode signals over extended 1310nm / 1550nm single-mode optical fiber spans.
• The VCL-2710, IEEE C37.94 Multi-Mode to Single Mode Optical Converter includes the clock synchronization and clock re-generation functions which allows it to transmit the IEEE C37.94 multi-mode signal over extended single-mode optical fiber links of up to 50dB optical link loss budget (i.e., a typical reach of approximately 160 KM or 100 miles).

• Provides 4 x IEEE C37.94 compliant interfaces for the VCL-MX Version-6 E1 PDH Multiplexer.
• Used to interface with current differential and distance protection relays.
• May be used for inter-connecting legacy voice and data networks, provisioning and managing bandwidth on a E1 channelized level as well as 64Kbps, DS-0 time-slot level and can be used as a digital-access cross-connect equipment.
• Provides 4 x Binary (110V DC / 220V DC) Commands Teleprotection interface for providing Distance Protection and IEEE C37.94 optical (MM / SM) ports for providing Distance / Differential Protection.

VCL-PMU-30 is a modular Phasor Measurement Unit (PMU) that is designed to provide measured Synchrophasor
values in accordance with the IEEE C37.118.1-2011 and C37.118.1a-2014 synchrophasor standards. With ever increasing
power demand, the power grid requires efficient and reliable technologies to monitor voltage, frequency, phase angle
and shifts in the power transmission network, in real-time, to detect grid imbalances which can result in catastrophic grid
failure and blackouts. The synchrophasor technology is used to monitor the power-grid in real time. The VCL-PMU-30
which uses synchrophasor technology, which may be used to provide precise data, in real-time, for steady-state and
dynamic-state conditions for both M class and P class, at the desired frame rates.

VCL-PDC (Phasor Data Concentrator) is a high-performance platform for managing Synchrophasor data and processing
streaming data in real-time. The VCL-PDC receives and time-synchronizes phasor data from multiple Phasor Measurement
Units (PMUs) to produce real-time, time-stamped output data stream. A PDC can simultaneously store and send PMU data
to multiple locations. By using multiple PDCs, customer can create multiple layers of concentration, within a Synchrophasor
data system. Various utilities are included to streamline the initial setup, configuration and testing process. The VCL-PDC
is a very versatile and easy-to-use phasor data concentrator.

Provides advanced protection against cyber threats, Denial of Service (DoS), ransom DDoS (RDDoS) attacks, with increase
security and mitigate network vulnerabilities. High data throughput options are designed to secure critical infrastructure
such as utilities, sub-stations, smart-grid distribution systems, airports and railways networks as well as IT Networks of financial institutions.

VCL Network-MouseTrαp^TM is an essential part of the digital forensics kit that sits behind the firewall in a secure
environment to detect firewall breaches and unauthorized intrusions in an IP network. It provides audio-visual alerts upon
detection of a network security breach. It finger-prints with time-stamp, including IP address, domain, location of the
intruder along with forensic analysis in real-time.

VCL provides a comprehensive “Beyond the Firewall” cyber security solutions that designed to assist organizations to prevent and secure their network against firewall breaches and cyber-attacks in real-time. The VCL-2702: Network Isolation Switch is one such element that forms a part of the cyber security suite of products that are offered by VCL.

VCL-2142 Enigmatron Xcöde is low data rate encryption equipment with extremely advanced features to secure and protect RTU data in critical infrastructure, Smart Grid Distribution Systems, Oil and Gas Infrastructure and Railway Signalling Networks. It provide secure communications between multiple RTU Terminals and their corresponding IEC 60870-5-104, MODBUS-TCP and DNP central server(s).

VCL-2140 is a low data rate Serial and Ethernet Data Encryption equipment with integrated firewall capabilities that may be installed to secure and protect ethernet and RTU data (Remote Terminal Data) in critical infrastructure, Smart Grid, Oil and Gas Infrastructure and Railway Signalling Networks. The VCL-2140 Data Encryption Equipment may be installed in point-to-point applications and used to provide to secure communications between the RTU Terminals and their corresponding IEC -101, -104, DNP, MODBUS protocol central servers.

VCL-2243 is a high-security, high-reliability, ruggedized, failsafe transparent RTU Firewall that is designed to be installed between the RTU and the SCADA server without having to reconfigure any element of the network. VCL-2243 firewall supports IEC 60870-5-104 (IEC 104), IEC 61850 MMS protocol, MODBUS protocol options with extremely advanced features that may be installed to secure and protect RTUs (Remote Terminal Units) in critical infrastructure.

VCL-2457, Rack Management and Fan Control Unit is designed to convert and transform standard equipement racks into “Smart-Racks”.

The VCL-5001, Network Traffic Sniffer is a cyber-security element that detects firewall breaches, network intrusions, data leaks and cyber-attacks in “real-time”. It also provides the user, the data to conduct forensic analysis and trace the attack route which assists the user to identify the points of network vulnerability and data leaks in their network.

VCL-MX-5010-R-ES is an integrated IEC-61850 compliant ruggedized router with enhanced security equipment with advanced features that may be installed to secure critical infrastructure such as utilities, sub-stations, smart-grid distribution systems, airports and railways as well as IT Networks of financial institutions such as banks and corporate networks.

VCL-MX-5020-R-ES is an integrated IEC-61850 compliant ruggedized router with Enhanced security equipment which has advanced features that may be installed to secure critical infrastructure such as utilities, sub-stations, smart-grid distribution systems, airports and railways as well as IT Networks of financial institutions such as banks and corporate networks.

VCL-MX-5040-R-ES is an integrated Router with Enhanced Security which has advanced features that may be installed to secure critical infrastructure such as utilities, sub-stations, smart-grid distribution systems, airports and railways as well as IT Networks of financial institutions such as banks and corporate networks.

VCL-MX-XW, Industrial Grade Ethernet, IEC 61850-3 complied Sub-Station Hardened Switch, is a flexible Ethernet Switch
that is packaged in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh environments. It requires no
external fans or forced air cooling.

VCL-MX-XW, is an IEC 61850-3 compliant, sub-station hardened, industrial grade 16 Port Ethernet Switch, that is packaged
in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh operational environments. It requires no external
fans or forced air cooling.

VCL-MX-XW, is an IEC 61850-3 compliant, sub-station hardened, industrial grade 24 Port Ethernet Switch, that is packaged in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh operational environments. It requires no external fans or forced air cooling.

The VCL-2725 is an industrial multirate media converter that is housed in a rugged aluminum chassis which is designed to convert 10/100/1000Base-T (Electrical Ethernet) signal into 100Base-FX or 1000Base-X (Optical Ethernet - Multirate) signal.

The VCL-2724, Parallel Redundancy Protocol (PRP) Switch allows the transmission of duplicated data over two parallel links, simultaneously, with zero packet loss.

The VCL-2486-G, GPS Receiver, Time Distribution Unit is designed to provide up to 16 outputs of Pulse and / or NMEA-0183 and / or IRIG-B and / or NTP (mix and match) that is locked to a GPS / GNSS Reference to provide time synchronization to private networks such as Railways and Metro networks, Airports and Air-Traffic Control facilities, Electric Sub-Stations,
Power Distribution and Transmission companies, Oil and Gas Utilities, ISPs and Cable TV networks as well as to Campus networks.

The VCL-2486-M 1:16 Pulse + NMEA Multiplexer is a compact and cost-effective solution to provide up to 16 Pulse;
NMEA-0183 outputs. It takes Pulse and one NMEA-0183 as input option to provide up to 16 Pulse outputs; or
8 Pulse + 8 NMEA outputs. It may be used to multiply 1 x 1PPS to 16 x 1PPS signals; or 1 x 1PPS and 1 x NMEA-0183 to
8 x 1PPS and 8 x NMEA-0183 outputs.

The VCL-2486-I, 1:16 IRIG-B Distribution Unit / IRIG-B Multiplier with BNC, RS-422 (RJ45) and IRIG-B optical outputs. The VCL-2486-I, IRIG-B Distribution Unit is a compact and cost-effective solution to provide up to 16 IRIG-B outputs. IRIG-B Distribution Unit takes one IRIG-B Input to provide up to 16 IRIG-B outputs. It is used to multiply 1 x IRIG-B to provide 16 x IRIG-B outputs.

VCL-2728 is a comprehensive 1PPS/IRIG-B over multi-mode optical fiber distribution solution which comprises of two units - VCL-2728-T and VCL-2728-R. VCL-2728-T, 1PPS/IRIG-B - Transmitter: converts a “1PPS/ IRIG-B Input” and transmits over a 850nm multi-mode optical fiber. VCL-2728-R, 1PPS/IRIG-B - Receiver: receives a “Optical 1PPS/IRIG-B Input” over 850nm multi-mode optical fiber and converts the optical input to 4 x 1PPS / 4 x IRIG-B BNC outputs.

Valiant’s VCL-1400, STM-16/64 SDH Multiplexer with MPLS-TP is a compact POTP platform which is targeted for deployment
in the edge and access part of a transport network. It can be configured both as a TDM MSPP as well as a Packet Switch.
It supports both TDM and Ethernet as Line Interfaces. It offers full redundancy and comes with an expansion chassis for deployment in high drop locations and can be used in point-to-point, linear, ring, T, and mesh networks.

Valiant’s VCL-1400, OC-48/192 SONET Multiplexer with MPLS-TP is a compact POTP platform which is targeted for
deployment in the edge and access part of a transport network. It can be configured both as a TDM MSPP as well as a
Packet Switch. It supports both TDM and Ethernet as Line Interfaces. It offers full redundancy and comes with an expansion chassis for deployment in high drop locations and can be used in point-to-point, linear, ring, T, and mesh networks.

Valiant's offers STM-1 63 E1 (Optical / Electrical), Add-Drop SDH Multiplexer unit is a modular platform unit with two 155.52Mbps optical / electrical interfaces, which may be used in a point-to-point, chain or ring application to provide an ultra-compact, cost effective and flexible multi-service platform.

63xE1 interfaces (120 Ohms [RJ-45] and 75 Ohms [BNC] options along with Engineering Order Wire is available. The user removable / replaceable STM-1 Optical / Electrical interface option makes it easy to meet various and changing user requirements. Valiant's STM-1, SDH Transmission Equipment provides full capability to cross-connect at E1 level between all tributaries.

Valiant offers STM-1 (Optical / Electrical), E1 and Ethernet Multi-Service SDH Transmission Unit is a modular platform unit with two 155.52Mbps optical / electrical interfaces, which may be used in a point-to-point, chain or ring application to provide an ultra-compact, cost effective and flexible multi-service platform.

Interface card options include the 8xE1 interface card (120 Ohms [RJ-45] and 75 Ohms [BNC]), 4x100BaseT Ethernet interface card (1 VCG, 4 Ports 1 Channel) and 4x100BaseT Ethernet interface card (4 VCG, 4 Ports 4 Channels) options along with Engineering Order Wire is available. The user removable / replaceable STM-1 Optical / Electrical interface option makes it easy to meet various and changing user requirements. Valiant's STM-1, E1 and Ethernet over SDH Transmission Equipment provides full capability to cross-connect at E1 level between all tributaries.

Valiant Communications offers STM-1 Optical to STM-1 Electrical converter provides a simple and cost-effective conversion between STM-1 optical interface and STM-1 electrical interface. STM-1 Optical to STM-1 Electrical converter is an interface conversion equipment supplied with one STM-1 electrical (75 Ohms BNC) interface and one STM-1 optical (MSA compliant SFP) interface.

STM-1 Optical to STM-1 Electrical converter is a compact solution housed in a 1U high (44mm), 19-inch rack-mountable shelf, which can be installed in any DIN-standard 19-inch rack

VCL-MX Version 6 - 80 x E1 Voice and Data Primary Multiplexer supports 160Mbps, 80 E1 fully non-blocking cross-connect
at 64Kbps (DS-0) level (2480 DS-0 – any to any time-slot cross-connect). This multi-service platform provides a wide variety
of voice and data services from single chassis. It offers 1+1 E1 Link Protection / E1 Port Redundancy (8 E1's per card), 
1+1 Control Card Processor Redundancy, 1+1 Cross-Connect / TSI Redundancy, 1+1 Timing (Synchronization Clock) Redundancy. User selectable synchronization priority, 1+1 48V DC Power Supply Redundancy (Dual Power Input – allows
the equipment to be powered from two separate sources). It also supports a variety of voice and data interfaces including
up to 144 FXO or 144 FXS voice channels per unit, up to 72 E&M 2-wire / 4-wire voice channels per unit.

VCL-MX Version 6 - 80 x E1 Voice and Data Primary Multiplexer supports 160Mbps, 80 E1 fully non-blocking cross-connect
at 64Kbps (DS-0) level (2480 DS-0 – any to any time-slot cross-connect). This multi-service platform provides a wide variety
of voice and data services from single chassis. It offers 1+1 E1 Link Protection / E1 Port Redundancy (8 E1's per card), 1+1 Control Card Processor Redundancy,  1+1 Cross-Connect / TSI Redundancy, 1+1 Timing (Synchronization Clock) Redundancy. User selectable synchronization priority, 1+1 48V DC Power Supply Redundancy (Dual Power Input – allows the equipment to be powered from two separate sources). It also supports a variety of voice and data interfaces including up to 144 FXO or 144 FXS voice channels per unit, up to 72 E&M 2-wire / 4-wire voice channels per unit.

Valiant's 4 x E1 Multiplexer the VCL-MX, 2Mbps E1 voice and data, drop-insert (add-drop) multiplexer Deluxe Version 2 is available with a wide range of voice (POTS) and digital data services to subscribers located at different locations, requiring to interconnect and establish a voice and data network over an E1 link. The VCL-MX is available in 3 versions, each providing different features and voice / data interfaces.

Valiant offers its 16 port E1 Digital Access Cross Connect Switch (DACS / DXC) (and T1 DACS) for applications including access cross-connect, Hi-Z (high impedance) monitoring, automatic protection switching (1+1 APS). All models are available with TCP-IP remote access and monitoring facility. The VCL-MegaConnect-Jr. 16 Port, E1 Digital Cross Connect Switch, is an E1 digital cross connect switch, which presents its user an easy to use, yet a sophisticated platform to cross connect up to 16 E1 ports. E1 Digital Cross Connect Switch offers full cross connect functionality to cross connect, and/or aggregate DS-0s, "n"x64Kbps consecutive data channels and fractional E1 channels to full E1 channels.

Valiant offers its 16 port T1 Digital Access Cross Connect Switch (DACS / DXC) (and E1 DACS) for applications including access cross-connect, Hi-Z (high impedance) monitoring, automatic protection switching (1+1 APS). All models are available with TCP-IP remote access and monitoring facility. VCL-MegaConnect-Jr. 16 Port, T1 Digital Cross Connect Switch, is an T1 digital cross connect switch, which presents its user an easy to use, yet a sophisticated platform to cross connect up to 16 T1 ports. T1 Digital Cross Connect Switch offers full cross connect functionality to cross connect, and/or aggregate DS-0s, "n"x64Kbps consecutive data channels and fractional T1 channels to full T1 channels.

80 E1 DXC / E1 DACS - VCL-MX Version 6 - Upto 80 E1, 160Mbps Digital Access Cross Connect is a modular switch which may be scaled from 8 E1 Ports to up to 80 E1 Ports. The DXC offers upto 160Mbps, 80 E1 fully non-blocking cross-connect at 64Kbps (DS-0) level (2480 DS-0 – any to any time-slot cross-connect), scalable from 8 E1 Ports to 80 E1 Ports, 1+1 Control Card Processor Redundancy, 1+1 Cross-Connect / TSI Redundancy, 1+1 Timing (Synchronization Clock) Redundancy, 1+1 -48V DC Power Supply Redundancy.

The VCL-MX Version 6 DXC 80 T1, 120Mbps Digital Access Cross Connect Switch, is a modular switch that may be scaled from 8 T1 Ports to up to 80 T1 Ports. The VCL-MX Version 6, T1 DACS (T1 DXC) offers full cross-connect functionality to cross-connect between 64Kbps time-slots ( DS-0s), “n"x64 Kbps consecutive DS-0s and Fractional T1 channels to full T1 channels.

64 E1 port intelligent (manageable) electronic patch panel allows the user to cross-connect any E1 port to any to any E1 ports, electronically, without having to use any external patch-cords or loose hanging wires. The E1 64 port electronic patch panel also provides the user with the capability to uni-directionally broadcast E1 inputs to multiple E1 destinations.

64 T1 port intelligent (manageable) electronic patch panel allows the user to cross-connect any T1 port to any to any T1 ports, electronically, without having to use any external patch-cords or loose hanging wires. The T1 64 port electronic patch panel also provides the user with the capability to uni-directionally broadcast T1 inputs to multiple T1 destination.

The VCL- E3-OLTE is a 34Mbps Optical Line Transmission Equipment which converts and transports a ITU-T compliant standard E3, 34Mbps signal on optical fiber. The optical link, between two OLTE terminals is established on one pair of optical fibers. One fiber link is used for Transmit and the other fiber link is used for Receive. A complete optical line transmission system comprises of two OLTE terminals one at each end of the optical fiber cable. Both the Local and the Remote terminals can be monitored and controlled by a Windows based GUI (Graphical User Interface).

4 E1 Optical Multiplexer with 100Mbps Ethernet data transmission rate solution is a high performance optical line transmission equipment, combines 4, ITU-T G.703 compliant standard electrical E1s plus 100Mbps ethernet signal into an optical data stream for transport over fiber optic pairs.

8 E1 Optical Multiplexer with 100Mbps Ethernet data transmission rate solution is a high performance optical line transmission equipment, combines 8, ITU-T G.703 compliant standard electrical E1s plus 100Mbps ethernet signal into an optical data stream for transport over fiber optic pairs.

Gigabit (Wire-Speed) Optical Multiplexer with 16 E1 interfaces is a unique Gigabit multi-service optical fiber transport solution which transmits both Gigabit Ethernet (Gigabit Wire Speed) data along with upto 16 E1 (TDM) channels over an optical fiber link.

Valiant’s Gigabit Ethernet over SDH (STM-1) provides a simple, cost effective and compact solution to convert 10/100/1000Base-T (Gigabit) data interface on the user side and transport Ethernet traffic over a STM-1 (155Mbps) SDH
link and reconstruct the data back to ethernet frame format, at remote end. The converter is an effective method for converting and transporting 10/100/1000Base-T (Gigabit) ethernet data over an STM-1 (155Mbps) SDH link.

VCL-GigEoSDH is a dual - VCG channel Gigabit Ethernet Converter, provides 4 gigabit Ethernet interfaces (3copper and 1 fiber Ethernet interfaces) compliant with IEEE 802.3 series standard and 2 STM-1 optical interfaces, supports 1+1 optical path protection and 2+0 mode. In 1+1 mode, the 4 Etherent interfaces share one VCG and the bandwidth is one VC4 (139Mb/s). In 2+0 mode, the 4 Ethernet interfaces share two VCG channels and the bandwidth is two VC4.

Valiant's Gigabit Ethernet over SDH (STM-4) Equipment is a compact and high-performance Gigabit Ethernet to STM-4 converter with VLAN TAG function), which offers three Gigabit Ethernet interfaces (2 Electrical and 1 Optical Ethernet interfaces) and 2 x STM-4 interfaces. The solution complies to ITU-T G.7041 and G.7042 EoSDH (Ethernet over SDH)
technology. All VC4 / STM-1 (1~8) are user configurable and may be mapped to a single VCG (single Ethernet Port),
when both STM-4 interfaces are independent. 3 x Gigabit Ethernet interfaces can share up to 1112Mbps (8 VC4).

Valiant’s Ethernet over SDH / STM-1 (EoS) provides a simple, cost effective and compact solution to convert 10/100BaseT data interface on the user side and transport Ethernet traffic over a STM-1 SDH link and reconstruct the data back to ethernet frame format, at remote end. The converter is an effective method for converting and transporting 10/100BaseT ethernet data over an STM-1 (SDH) link. Valiant is available in a 1U (44mm high) box in a 19-inch rack mount chassis.

Valiant Communications offers STM-1 Optical to STM-1 Electrical converter provides a simple and cost-effective conversion between STM-1 optical interface and STM-1 electrical interface. STM-1 Optical to STM-1 Electrical converter is an interface conversion equipment supplied with one STM-1 electrical (75 Ohms BNC) interface and one STM-1 optical (MSA compliant SFP) interface. 1+1, STM-1 Optical to STM-1 Electrical converter option is also offered and available. STM-1 Optical to STM-1 Electrical converter is a compact solution housed in a 1U high (44mm), 19-inch rack-mountable shelf, which can be installed in any DIN-standard 19-inch rack.

Valiant offers its Ethernet over DS3 Switch (Ethernet to DS3 Switch) packaged in a 1U, 19-inch rack-mountable chassis. Valiant Ethernet over DS3 Switch (Ethernet over DS3 Switch) provides a four 100BaseT Ethernet and 100Base-FX optical (optional) ethernet interfaces on the user side which may be used to transport Ethernet traffic over a DS3 link. Both ethernet interfaces may be used simultaneously. The Switch provides a simple and cost effective method to convert and transport ethernet data over an DS3 link.

Valiant offers its Ethernet to E3 converters (Ethernet over E3 Converters) packaged in a 19-inch rack-mountable chassis. Provides framed and un-framed E3 options. Valiant Ethernet to E3 converters (Ethernet over E3 Converters) provides a 100BaseT data interface on the user side which may be used to transport Ethernet traffic over a E3 link. The converter provides a simple and cost effective method to convert and transport 100BaseT ethernet data over a E3 link.

Valiant’s VCL-ETH-8E1-ML / VCL-ETH-16E1-ML / VCL-ETH-24E1-ML Converter allows the user to send Ethernet data between two points or between multiple points (maximum 16 directions), over 8/16/24 E1 Links respectively. E1 Interfaces options are 75 Ohms/120 Ohms (Optional – as per user requirement). This equipment provides two Electrical Gigabit (1000/100/10M) Ethernet Interfaces (RJ-45) ports at the customer site. The equipment supports point-to-point - multilink protocol which allows a single unit to be connected to multiple units.

Valiant offer its Ethernet over 1 E1 converter. The 10Base-T Ethernet interface to 1 E1 interface converter which offers a channelized E1 and 10Base-T interface conversion. This equipment offers electrical level conversion between 10Base-T Ethernet interface and a G.703 / E1 (or fractional E1) interfaces. The VCL-Ethernet over E1-E1/10(100) Base-T Interface Converter provides the user with Ethernet over E1/E1 conversion enabling the user to transport Ethernet data over an E1 link. The equipment be always installed and used in pairs, with one terminal being installed at either end of the network.

Valiant offers its 4 x Ethernet over T1 (IP over TDM) package in a 1U High, 19-inch rack-mountable chassis. It provides four 10/100BaseT (4 RJ-45) data interfaces on the user side which may be used to transport Ethernet traffic over a T1 link. The converter provides a simple and cost effective method to convert and transport Ethernet data over a T1 link. Ethernet over T1 is an Ethernet extension device utilizing TDM telecom infrastructure (of T1, DS3, SDH or microwave links carrying T1s ). It converts the Ethernet data into T1 frame format for transmission over the existing TDM (T1) links and then re-converts the T1 back into Ethernet data the far-end terminal, to BRIDGE two Ethernet LANs over the existing T1-based telecom network.

Valiant Ethernet over 4E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link. This equipment is available in 4E1, 8E1 and 16E1 Port versions.

Valiant Ethernet over 4E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link. This equipment is available in 4E1, 8E1 and 16E1 Port versions.

Valiant’s Ethernet over 8E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. This equipment is available in 4E1, 8E1 and 16E1 Port versions. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link.

Valiant’s Ethernet over 16E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. This equipment is available in 4E1, 8E1 and 16E1 Port versions. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link.

VCL-E1oP' E1 over Packet (2 E1 Port FE Version) TDM over IP equipment supports transmission of up to 2 x E1 links over
IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched
Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (2 E1 Port GE Version) TDM over IP equipment supports transmission of up to 2 x E1 links over
IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched
Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (4 E1 Port FE Version) TDM over IP equipment supports transmission of up to 4 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (8 E1 Port GE Version) TDM over IP equipment supports transmission of up to 8 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (16 E1 Port GE Version) TDM over IP equipment supports transmission of up to 16 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

VCL-E1oP' E1 over Packet, 32 E1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x E1 links over IP / Ethernet, MEF or MPLS networks. Multiple units of the 32 E1 Port GE Version equipment may be cascaded to support 32 E1 Ports aggregation at the Central Office / MSC (Mobile Switching Center). Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (2 T1 Port FE Version) TDM over IP equipment supports transmission of up to 2 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (2 T1 Port GE Version) TDM over IP equipment supports transmission of up to 2 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (4 T1 Port FE Version) TDM over IP equipment supports transmission of up to 4 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (8 T1 Port GE Version) TDM over IP equipment supports transmission of up to 8 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (16 T1 Port GE Version) TDM over IP equipment supports transmission of up to 16 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet 32 T1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x T1 links over IP / Ethernet, MEF or MPLS networks. Multiple units of the 32 E1 Port GE Version equipment may be cascaded to support 32 T1 Ports aggregation at the Central Office / MSC (Mobile Switching Center). Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-DS3oP', DS3 (T3) over IP / Ethernet / Packet equipment provides transmission of one, point-to-point, DS3 (T3) link over an IP / Ethernet, MEF or MPLS / Packet network. The 'VCL-DS3oP', DS3 (T3) over IP / Ethernet equipment is powered by a powerful PowerPC 400 MHz Processor which provides a highly reliable clock recovery mechanism for low jitter and wander control, even under variable network conditions.

'VCL-E3oP' (E3 over IP/Packet/Ethernet) equipment is used to transport a single E3 interface over an IP, MPLS or Ethernet / Packet network. The VCL-E3oP' (E3 over IP) equipment, is equipped with a powerful PowerPC 400 MHz Processor which provides a highly reliable clock recovery mechanism for low jitter and wander control, even under variable network conditions.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.

The VCL-SafeComm, 8 E1 Links (24 E1 Ports), 1+1 Automatic Protection / AB Fallback Switching Equipment may be used to protect upto 8 E1 Links (24 E1 Ports), point-to-point links and provide an alternate communication route to each E1 Link between any two E1 points. In the event of the failure of the primary (Main) E1 communication route, the VCL-SafeComm,
8 E1 Links (1+1 Automatic Protection / AB Fallback Switching Equipment) automatically switches the E1 traffic to a
secondary (standby) E1 route. The VCL-SafeComm, 8 E1, 1+1 Automatic Protection / AB Fallback Switching equipment is available in a 2U high chassis which may be mounted in any DIN standard,19-Inch rack.

The VCL-SafeComm, 16 E1 Links (48 E1 Ports), 1+1 Automatic Protection / AB Fallback Switching Equipment may be used to protect upto 16 E1 Links (48 E1 Ports), point-to-point links and provide an alternate communication route to each E1 Link between any two E1 points. In the event of the failure of the primary (Main) E1 communication route, the VCL-SafeComm,
16 E1 Links (1+1 Automatic Protection / AB Fallback Switching Equipment) automatically switches the E1 traffic to a
secondary (standby) E1 route. The VCL-SafeComm, 16 E1, 1+1 Automatic Protection / AB Fallback Switching equipment is available in a 2U high chassis which may be mounted in any DIN standard,19-Inch rack.

The VCL-SafeComm, 8 T1 Links (24 T1 Ports), 1+1 Automatic Protection / AB Fallback Switching Equipment may be used to protect upto 8 T1 Links (24 T1 Ports), point-to-point links and provide an alternate communication route to each T1 Link between any two T1 points. In the event of the failure of the primary (Main) T1 communication route, the VCL-SafeComm, 8 T1 Links (1+1 Automatic Protection / AB Fallback Switching Equipment) automatically switches the T1 traffic to a secondary (standby) T1 route. The VCL-SafeComm, 8 T1, 1+1 Automatic Protection / AB Fallback Switching equipment is available in a 2U high chassis which may be mounted in any DIN standard, 19-Inch rack.

The VCL-SafeComm, 16 T1 Links (48 T1 Ports), 1+1 Automatic Protection / AB Fallback Switching (APS) Equipment may be used to protect upto 16 T1 Links (48 T1 Ports), point-to-point links and provide an alternate communication route to each T1 Link between any two T1 points. In the event of the failure of the primary (Main) T1 communication route, the VCL-SafeComm, 16 T1 Links (1+1 Automatic Protection / AB Fallback Switching Equipment) automatically switches the T1 traffic to a secondary (standby) T1 route. The VCL-SafeComm, 16 T1, 1+1 Automatic Protection / AB Fallback Switching equipment is available in a 2U high chassis which may be mounted in any DIN standard,19-Inch rack.

Valiant's E1 Fail-Over (E1 Protection) Switch (12 E1 Ports - 4 Links) allows the user to connect a single E1 line from the telephone company to an "active", as well as to a "standby" E1 terminal, such as data server / router etc. at the customer premises.

Valiant's T1 Fail-Over (T1 Protection) Switch (12 T1 Ports - 4 Links) allows the user to connect a single T1 line from the telephone company to an "active", as well as to a "standby" T1 terminal, such as data server / router etc. at the customer premises.

Valiant's DS3 Protection (Fail Over) Switch allows the user to connect a single DS3 line from the telephone company to an "active", as well as to a "standby" DS3 terminal, such as data server, router etc. at the customer premises.

Valiant's E3 Fail Over (E3 Protection) Switch allows the user to connect a single E3 line from the telephone company to an "active", as well as to a "standby" E3 terminal, such as data server / router etc., at the customer premises.

Valiant's ‘VCL-PG, 16/32E1 Packet Monitoring Solution’ may be used to groom up to 16 / 32 x E1 channels and convert
their payload to RFC 5086, RFC 5087 and RFC 4553 compliant Ethernet Packets. The VCL-PG, 16/32E1 Packet Monitoring Solution is equipped with a highly reliable clock recovery mechanism for low jitter and wander control, even under variable network conditions.

VCL-STM-1 Monitoring Groomer is a cost-effective monitoring and grooming equipment which may be used to "non-intrusively" monitor "bi-directional" STM-1 links through a 80:20 optical splitter patch panel and allow the user to select
64Kbps time-slots and groom them to E1 output ports, which may be then connected to E1 probes, E1 signaling
analyzers and billing servers etc.

VCL-MegaConnect, the E1 (also available in T1) 16 port Hi-Z Monitoring Groomer is available for non-intrusive live traffic monitoring (high impedance) applications in which E1 (or T1) ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc.

VCL-MegaConnect, the E1 x 32 port Hi-Z Monitoring Groomer is available for special non-intrusive monitoring (high impedance) applications in which E1 (and T1) ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc. In the monitoring mode the groomer provides the user a total of 36, E1 Ports.

VCL-MegaConnect, the T1 x 32 port Hi-Z Monitoring Groomer is available for special non-intrusive monitoring (high impedance) applications in which T1 ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc. In the monitoring mode the groomer provides the user a total of 36, T1 ports.

The VCL-MegaConnect, 64 Port Plus - E1 Monitoring Groomer is suitable for non-intrusive monitoring of upto 32, "live" E1 traffic links, bidirectionally (i.e. in both transmit and receive directions through its 64 E1 receivers) through a high impedance (Hi-Z) path. Additionally, the equipment also provides 16 output E1 ports that shall connect the aggregated time-slots which have been non-intrusively "monitored" from the 32, "live" E1 traffic links to the user's protocol analysers, test probes, etc.

The VCL-MegaConnect, 64 Port Plus - T1 Monitoring Groomer is suitable for non-intrusive monitoring of upto 32, "live" T1 traffic links, bidirectionally (i.e. in both transmit and receive directions through its 64 T1 receivers) through a high impedance (Hi-Z) path. Additionally, the equipment also provides 16 output T1 ports that shall connect the aggregated time-slots which have been non-intrusively "monitored" from the 32, "live" T1 traffic links to the user's protocol analysers, test probes, etc.

VCL-64HSL, 64 Port E1, HSL (High Speed Signaling Link) Monitoring equipment is suitable for "non-intrusive" monitoring application and for monitoring of upto 32, "live" HSL E1 (High Speed Signaling Link) traffic links, bi-directionally (i.e. in both transmit and receive directions). The equipment can be used to monitor all types of E1 links (fractional or whole, unframed, framed).

VCL-64HSL, 64 Port T1, HSL (High Speed Signaling Link) Monitoring equipment is suitable for "non-intrusive" monitoring application and for monitoring of upto 32, "live" HSL T1 (High Speed Signaling Link) traffic links, bi-directionally (i.e. in both transmit and receive directions). The equipment can be used to monitor all types of T1 links (fractional or whole, unframed, framed).

Valiant offers a compact, robust and cost effective E1 echo canceller solution in 19 inch, 1U high (44mm height) chassis (accommodates 1, E1 echo canceller per shelf). Echo cancellation on each channel is 64ms Bi-Directional / 128ms. Uni-Directional echo tails - user selectable.

Valiant offers a compact, robust and cost effective T1 echo canceller solution in 19 inch, 1U high (44mm height) chassis (accommodates 1, T1 echo canceller per chassis). Echo cancellation on each channel is 64ms Bi-Directional / 128ms. Uni-Directional echo tails - user selectable.

Valiant offers the industry's most compact 8, E1 echo canceller with voice quality enhancement (VQE) solution in a 19-inch, 1U (44mm height) chassis, with echo-tail displacement feature which is user programmable from 0ms. to 896ms. Echo cancellation on each channel is 128ms. bi-directional.

Valiant offers the industry's most compact 8, T1 echo canceller with voice quality enhancement (VQE) solution in a 19-inch, 1U (44mm height) chassis, with echo-tail displacement feature which is user programmable from 0ms. to 896ms. Echo cancellation on each channel is 128ms. bi-directional.

VCL-3010, RS232 to Ethernet Converter is a ruggedized and robust, sub-station-hardened protocol converter which shall convert Serial RS232 data to Ethernet data. VCL-3010 supports point-to-point application.

VCL-3020, RS232 to Ethernet Converter is a ruggedized and robust, sub-station-hardened protocol converter which shall convert Serial RS232 data to Ethernet data. VCL-3020 supports point-to-point and point-to-multi-point conference application in which one VCL-3020 can communicate up to 5 x VCL-3010 / Slave devices at a time.

VCL-3030, IEC 60870-5-101 to 60870-5-104 / MODBUS to Ethernet Protocol Converter is a ruggedized and robust, sub-station-hardened protocol converter which shall convert Serial -101 to Ethernet -104 and Serial MODBUS to Ethernet data.

VCL-3040, Quad RS232 to RS485 Converter is a ruggedized, robust, sub-station-hardened protocol converter which converts the Serial RS232 data in to RS485 data and vice versa. VCL-3040 is a bi-directional serial ethernet interface converter which enables the interconnectivity between Ethernet and serial RS232 / RS485 interfaces.

64 E1 port intelligent (manageable) electronic patch panel allows the user to cross-connect any E1 port to any to any
E1 ports, electronically, without having to use any external patch-cords or loose hanging wires. The E1 64 port electronic
patch panel also provides the user with the capability to uni-directionally broadcast E1 inputs to multiple E1 destinations.

64 T1 port intelligent (manageable) electronic patch panel allows the user to cross-connect any T1 port to any to any
T1 ports, electronically, without having to use any external patch-cords or loose hanging wires. The T1 64 port electronic
patch panel also provides the user with the capability to uni-directionally broadcast T1 inputs to multiple T1 destinations.

16 x E1, 120 Ohms, 16 Port Patch Panel with High Impedance (Hi-z) Monitoring Ports is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications. Available in 19 Inch Rack Mount.

16 x E1, 75 Ohms, 16 Port Patch Panel with High Impedance (Hi-z) Monitoring Ports is primarily designed for applications where E1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications. Available in 19 Inch Rack Mount. 75 Ohms Patch Panels with High Impedance (Hi-z) Monitoring Ports are available with various 75 Ohms BNC, BT43, M4 (Male), M4 (Female), Siemens (1.6/5.6 Female) Connector options. Please ask for data sheet for any of these 75 Ohms connector options.

16 x T1, 100 Ohms, 16 Port Patch Panel with High Impedance (Hi-z) Monitoring Ports is primarily designed for applications where T1 circuits are required to be "patched" as well as simultaneously "tapped" for non-intrusive monitoring applications. Available in 19 Inch Rack Mount.

16 E1, G.703 balun panel with 120 Ohms (RJ45) to E1, 75 Ohms (BNC Female Connector) converter panel, may be used to convert up to 16, E1, 120 Ohms balanced (RJ45) Interfaces to E1, 75 Ohms un-balanced (BNC Female Connector) Interfaces. 19 Inch Rack Mount.

16 E1, G.703 balun panel with 120 Ohms (RJ45) to E1, 75 Ohms (1.6 / 5.6 Female Connector) converter panel, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (1.6 / 5.6 Female Connector) Interfaces. 19 Inch Rack Mount.

16 E1, G.703 balun panel with 120 Ohms (RJ45) to E1, 75 Ohms (BT43 Male Connector) converter panel, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (BT43 Male Connector) Interfaces. 19 Inch Rack Mount.

16 E1, G.703 balun panel with 120 Ohms (RJ45) to E1, 75 Ohms (M4 Female Connector) converter panel, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (M4 Female Connector) Interfaces. 19 Inch Rack Mount.

16 E1, G.703 balun panel with 120 Ohms (RJ45) to E1, 75 Ohms (M4 Female Connector) converter panel, may be used to convert up to 16, E1, 120 Ohms (RJ45) Interfaces to E1, 75 Ohms (M4 Female Connector) Interfaces. 19 Inch Rack Mount.

Dual Balun (Shielded) 2 x BNC (F) (75 Ohms) to RJ-45 (F) 120 Ohms Converter

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to 48V DC output voltage. It may be also used to convert 120V DC - 370V DC Input Voltage to 48V DC Output Voltage. Available with 3.2 Amps (150 Watts). 4 fuse protected outputs. 19 Inch Rack Mount Version.

Valiant’s AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to 48V DC output voltage. It may be also used to convert 120V DC - 373V DC Input Voltage to 48V DC Output Voltage. The AC to DC / DC to DC converter is designed for telecom applications requiring stable DC voltage with low EMI and EMC interference. This is an external converter power supply which is available in a portable desktop and 19 inch rack mount version, with four fuse protected outputs in the rack mount version.

DC to DC Converter - 48V DC (range DC 36-76) to 24V DC converter. This DC to DC converter may be used to convert 48V DC (range 36V DC to 76V DC) Main Input Voltage to 24V DC output voltage. Available with 4.2 Amps (100 Watts) with 4 fuse protected outputs. 19 Inch Rack Mount Version.

DC to DC converter may be used to convert 90V DC ~ 373V DC Input Voltage to 48V DC output voltage. It may be also used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to 48V DC Output Voltage. The DC to DC converter is designed for telecom applications requiring stable DC voltage with low EMI and EMC interference. This is an external converter power supply which is available in 19 inch rack mount version, with four fuse protected outputs.

AC to DC converter may be used to convert 85V AC-264V AC, 47Hz-63Hz AC Mains Input Voltage to 24V DC output voltage. It may be also used to convert 120V DC - 370V DC Input Voltage to 24V DC Output Voltage. Available with 6.3 Amps (150 Watts), 4 fuse protected outputs. 19 Inch Rack Mount Version.

What does it do?
The 16 x E1 (120 Ohms) Splitter “Splits” the E1 signal that it receives between two E1 ports, by monitoring the same E1 signal on two ports, simultaneously.

What does it do?
The 16 x E1 (120 Ohms) Splitter “Splits” the E1 signal that it receives between two E1 ports, by monitoring the same E1 signal on two ports, simultaneously.