VCL Solutions

VCL offers a wide range of GPS / GNSS Primary Reference Clocks (ITU-T G.811) and SSU (Synchronization Supply Unit), a 1+1 fully redundant architecture. Applications include synchronization for Utilities including Power Generation / Distribution / Transmission, Railways / Metro, Airports (including Air-Traffic Control), 2G, 3G, 4G, 5G mobile telecommunications networks, Micro Cell sites and backhaul wireline SDH / SONET and Synchronous Ethernet networks.

VCL offers a very wide range of NTP Time Servers that are designed to provide NTP Time and ITU-T G.811 Primary Reference Clock that is locked to a GPS / GNSS reference to provide time synchronization to private networks such as Railways and Metro (ticketing and platform) networks, Airports and Air-Traffic Control facilities, Electric Sub-Stations, Power Distribution and Transmission companies, Oil and Gas Utilities, ISPs and Cable TV networks as well as to Campus networks that are required to maintain a complete isolation from public networks for security reasons.

VCL offers a very wide range of PTP IEEE-1588v2 (Precision Time Protocol) based solutions. These include PTP 1588v2 Grandmaster Clocks, PTP 1588v2 Slaves with 1PPS, NMEA, 10MHz, 2.048MHz, 1.544Mbits / 2.048Mbits Frequency Outputs, PTP 1588v2 Aware Switch, PTP Transparent Clock and PTP to IRIG-B converter. The VCL PTP equipment is designed to be used in both contemporary and legacy synchronization applications.

VCL offers a very wide range of Time Distribution Solutions that are suitable for power and telecom applications. Power applications include power generation and power distribution infrastructure as well as other miscellaneous utility applications which require a highly precise time-of-day and 1 PPS synchronization locked to a GPS / GNSS Reference to distribute highly precise 1 PPS / IRIG-B time-of-day synchronization across all nodes of their networks.

The VCL offers a wide range of Time Distribution Solutions for NTP Client, IRIG-B (RS-422, RS-232, RS-485), IRIG-B optical, 1PPS, NMEA (0183). Customers can extract multiple 1PPS, Pulse, modulated IRIG-B (RJ45), Unmodulated IRIG-B (RS422 / BNC), NMEA outputs from GPS / GNSS source.

'VCL-E1oP' E1 over Packet (2 E1 Port FE Version) TDM over IP equipment supports transmission of up to 2 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (2 E1 Port GE Version) TDM over IP equipment supports transmission of up to 2 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-E1oP' E1 over Packet (4 E1 Port FE Version) TDM over IP equipment supports transmission of up to 4 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

VCL-MegaConnect, the E1 x 32 port Hi-Z Monitoring Groomer is available for special non-intrusive monitoring (high impedance) applications in which E1 (and T1) ports can be connected to monitoring / billing equipment for non-intrusive monitoring of live traffic or signaling, required by billing servers etc. In the monitoring mode the groomer provides the user a total of 36, E1 Ports.

'VCL-E1oP' E1 over Packet (16 E1 Port GE Version) TDM over IP equipment supports transmission of up to 16 x E1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional E1 data rates of 64Kbps to 2.048Mbps on each E1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

VCL-E1oP' E1 over Packet, 32 E1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x E1 links over IP / Ethernet, MEF or MPLS networks. Multiple units of the 32 E1 Port GE Version equipment may be cascaded to support 32 E1 Ports aggregation at the Central Office / MSC (Mobile Switching Center).

'VCL-T1oP' T1 over Packet (2 T1 Port FE Version) TDM over IP equipment supports transmission of up to 2 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (2 T1 Port GE Version) TDM over IP equipment supports transmission of up to 2 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (4 T1 Port FE Version) TDM over IP equipment supports transmission of up to 4 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (8 T1 Port GE Version) TDM over IP equipment supports transmission of up to 8 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet (16 T1 Port GE Version) TDM over IP equipment supports transmission of up to 16 x T1 links over IP / Ethernet, MEF or MPLS networks. Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-T1oP' T1 over Packet 32 T1 Port GE Version of our TDM over IP equipment supports transmission of up to 32 x T1 links over IP / Ethernet, MEF or MPLS networks. Multiple units of the 32 E1 Port GE Version equipment may be cascaded to support 32 T1 Ports aggregation at the Central Office / MSC (Mobile Switching Center). Other features supported are Circuit Emulation Service over Packet Switched Network / CESoPSN, PWE3 (pseudo-wire), SAToP, Fractional T1 data rates of 64Kbps to 1.544Mbps on each T1 port, Differentiated Services (Diffserv), QoS, Point-to-point, point-to-multipoint drop and insert applications.

'VCL-DS3oP', DS3 (T3) over IP / Ethernet / Packet equipment provides transmission of one, point-to-point, DS3 (T3) link over an IP / Ethernet, MEF or MPLS / Packet network. The 'VCL-DS3oP', DS3 (T3) over IP / Ethernet equipment is powered by a powerful PowerPC 400 MHz Processor which provides a highly reliable clock recovery mechanism for low jitter and wander control, even under variable network conditions.

'VCL-E3oP' (E3 over IP/Packet/Ethernet) equipment is used to transport a single E3 interface over an IP, MPLS or Ethernet / Packet network. The VCL-E3oP' (E3 over IP) equipment, is equipped with a powerful PowerPC 400 MHz Processor which provides a highly reliable clock recovery mechanism for low jitter and wander control, even under variable network conditions.

Valiant’s Gigabit Ethernet over SDH (STM-1) provides a simple, cost effective and compact solution to convert 10/100/1000Base-T (Gigabit) data interface on the user side and transport Ethernet traffic over a STM-1 (155Mbps) SDH link and reconstruct the data back to ethernet frame format, at remote end. The converter is an effective method for converting and transporting 10/100/1000Base-T (Gigabit) ethernet data over an STM-1 (155Mbps) SDH link.

Valiant's Gigabit Ethernet over SDH (STM-4) Equipment is a compact and high-performance Gigabit Ethernet to STM-4 converter (with VLAN TAG function), which offers three Gigabit Ethernet interfaces (2 Electrical and 1 Optical Ethernet interfaces) and 2 x STM-4 interfaces. The solution complies to ITU-T G.7041 and G.7042 EoSDH (Ethernet over SDH) technology. All VC4 / STM-1 (1~8) are user configurable and may be mapped to a single VCG (single Ethernet Port), when both STM-4 interfaces are independent.

Valiant’s Ethernet over SDH / STM-1 (EoS) provides a simple, cost effective and compact solution to convert 10/100BaseT data interface on the user side and transport Ethernet traffic over a STM-1 SDH link and reconstruct the data back to ethernet frame format, at remote end. The converter is an effective method for converting and transporting 10/100BaseT ethernet data over an STM-1 (SDH) link. Valiant is available in a 1U (44mm high) box in a 19-inch rack mount chassis.

Valiant Communications offers STM-1 Optical to STM-1 Electrical converter provides a simple and cost-effective conversion between STM-1 optical interface and STM-1 electrical interface. STM-1 Optical to STM-1 Electrical converter is an interface conversion equipment supplied with one STM-1 electrical (75 Ohms BNC) interface and one STM-1 optical (MSA compliant SFP) interface. 1+1, STM-1 Optical to STM-1 Electrical converter option is also offered and available.

Valiant offers its Ethernet over DS3 Switch (Ethernet to DS3 Switch) packaged in a 1U, 19-inch rack-mountable chassis. Ethernet over DS3 Switch (Ethernet over DS3 Switch) provides a four 100BaseT Ethernet and 100Base-FX optical (optional) ethernet interfaces on the user side which may be used to transport Ethernet traffic over a DS3 link. Both ethernet interfaces may be used simultaneously. The Switch provides a simple and cost effective method to convert and transport ethernet data over an DS3 link.

Valiant offers its Ethernet to E3 converters (Ethernet over E3 Converters) packaged in a 19-inch rack-mountable chassis. Provides framed and un-framed E3 options. Ethernet to E3 converters (Ethernet over E3 Converters) provides a 100BaseT data interface on the user side which may be used to transport Ethernet traffic over a E3 link. The converter provides a simple and cost effective method to convert and transport 100BaseT ethernet data over a E3 link.

Valiant’s VCL-ETH-8E1-ML / VCL-ETH-16E1-ML Converter allows the user to send Ethernet data between two points or between multiple points (maximum 12 directions), over 8/16 E1 Links respectively. E1 Interfaces options are 75 Ohms/120 Ohms (Optional – as per user requirement). This equipment provides two Electrical Gigabit (1000/100/10M) Ethernet Interfaces (RJ-45) ports at the customer site.

Valiant offer its Ethernet over 1 E1 converter. The 10Base-T Ethernet interface to 1 E1 interface converter which offers a channelized E1 and 10Base-T interface conversion. This equipment offers electrical level conversion between 10Base-T Ethernet interface and a G.703 / E1 (or fractional E1) interfaces. The VCL-Ethernet over E1-E1/10(100) Base-T Interface Converter provides the user with Ethernet over E1/E1 conversion enabling the user to transport Ethernet data over an E1 link.

Valiant offers its 4 x Ethernet over T1 (IP over TDM) package in a 1U High, 19-inch rack-mountable chassis. It provides four 10/100BaseT (4 RJ-45) data interfaces on the user side which may be used to transport Ethernet traffic over a T1 link. The converter provides a simple and cost effective method to convert and transport Ethernet data over a T1 link.

Valiant Ethernet over 4E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link.

Valiant’s Ethernet over 8E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link.

Valiant’s Ethernet over 16E1 Converter allows the user to send Ethernet data, between two points, over E1 Links. E1 Interfaces are 75 Ohms / 120 Ohms. Ethernet Interface options may be ordered as 10/100 Base-T Electrical Ethernet or 100Base-FX Optical Ethernet over 850nm / 1310nm / 1550nm single mode optical fiber interfaces. The equipment must be always installed and used in pairs, with one terminal being installed at either end of the E1 Link.

VCL IP/MPLS Router is a family of intelligent MPLS (Multiprotocol Label Switching) Routers which can be used to securely inter-connect multiple LAN networks over a WAN link using a choice of secure routing protocols including MPLS VPN, L2TPv3, L2VPN, L3VPN, IPSec and routing protocols including OSPF v2/v3, BGPv4, IS-IS, RIP v1/v2, ARP, IP Forwarding, VRRP, Layer 3 Routing and IPv4 / IPv6 features etc.

The VCL “Beyond the Firewall” cyber-security solutions are designed to assist organizations to detect, prevent and secure their network against firewall breaches, cyber-attacks, ransomware-attacks, DoS attacks, conduct forensic analysis and trace the attack route in real-time. Most network administrators rely solely on a “Firewall” to secure their IP networks.

VCL-MX-XW, Industrial Grade Ethernet, IEC 61850-3 complied Sub-Station Hardened Switch, is a flexible Ethernet Switch that is packaged in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh environments. It requires no external fans or forced air cooling. This IEC 61850-3 complied switch offers a wide choice of 1+1 redundant power supply options which include 24V DC, -48V DC, 110-125V DC, 110V AC and 240V AC.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.

VCL offers a wide range of GPS / GNSS Primary Reference Clocks (ITU-T G.811) and SSU (Synchronization Supply Unit), a 1+1 fully redundant architecture. Applications include synchronization for Utilities including Power Generation / Distribution / Transmission, Railways / Metro, Airports (including Air-Traffic Control), 2G, 3G, 4G, 5G mobile telecommunications networks, Micro Cell sites and backhaul wireline SDH / SONET and Synchronous Ethernet networks.

VCL offers a very wide range of NTP Time Servers that are designed to provide NTP Time and ITU-T G.811 Primary Reference Clock that is locked to a GPS / GNSS reference to provide time synchronization to private networks such as Railways and Metro (ticketing and platform) networks, Airports and Air-Traffic Control facilities, Electric Sub-Stations, Power Distribution and Transmission companies, Oil and Gas Utilities, ISPs and Cable TV networks as well as to Campus networks that are required to maintain a complete isolation from public networks for security reasons.

Valiant offers next generation STM-1 (optical and electrical), STM-4, STM-16, STM-64 with MPLS-TP SDH multiplexers and SONET Multiplexer with MPLS-TP, T1, T3/DS3, OC-3, OC-12, OC-48, OC-192, FE/GE/10GE to provide multiple services. The SDH / SONET Multiplexer with MPLS-TP is a compact, modular, and cost effective multiplexer equipment designed to manage bandwidth and provide E1/T1, E3/DS3, FE/GE/10GE interfaces.

VCL IP/MPLS Router is a family of intelligent MPLS (Multiprotocol Label Switching) Routers which can be used to securely inter-connect multiple LAN networks over a WAN link using a choice of secure routing protocols including MPLS VPN, L2TPv3, L2VPN, L3VPN, IPSec and routing protocols including OSPF v2/v3, BGPv4, IS-IS, RIP v1/v2, ARP, IP Forwarding, VRRP, Layer 3 Routing and IPv4 / IPv6 features etc.

The VCL “Beyond the Firewall” cyber-security solutions are designed to assist organizations to detect, prevent and secure their network against firewall breaches, cyber-attacks, ransomware-attacks, DoS attacks, conduct forensic analysis and trace the attack route in real-time. Most network administrators rely solely on a “Firewall” to secure their IP networks.

VCL-MX-XW, Industrial Grade Ethernet, IEC 61850-3 complied Sub-Station Hardened Switch, is a flexible Ethernet Switch that is packaged in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh environments. It requires no external fans or forced air cooling. This IEC 61850-3 complied switch offers a wide choice of 1+1 redundant power supply options which include 24V DC, -48V DC, 110-125V DC, 110V AC and 240V AC.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.

VCL offers a wide range of GPS / GNSS Primary Reference Clocks (ITU-T G.811) and SSU (Synchronization Supply Unit), a 1+1 fully redundant architecture. Applications include synchronization for Utilities including Power Generation / Distribution / Transmission, Railways / Metro, Airports (including Air-Traffic Control), 2G, 3G, 4G, 5G mobile telecommunications networks, Micro Cell sites and backhaul wireline SDH / SONET and Synchronous Ethernet networks.

Valiant offers next generation STM-1 (optical and electrical), STM-4, STM-16, STM-64 with MPLS-TP SDH multiplexers and SONET Multiplexer with MPLS-TP, T1, T3/DS3, OC-3, OC-12, OC-48, OC-192, FE/GE/10GE to provide multiple services. The SDH / SONET Multiplexer with MPLS-TP is a compact, modular, and cost effective multiplexer equipment designed to manage bandwidth and provide E1/T1, E3/DS3, FE/GE/10GE interfaces.

Valiant offers a wide range of Serial to Ethernet, IEC 60870-5-101 to 60870-5-104 Protocol Converter and MODBUS Converters. RS232 to Ethernet Converter with point-to-point and point-to-multi-point application. Valiant also offers Quad RS232 to RS485 robust, sub-station-hardened converter which converts the Serial RS232 data in to RS485 data and vice versa.

VCL IP/MPLS Router is a family of intelligent MPLS (Multiprotocol Label Switching) Routers which can be used to securely inter-connect multiple LAN networks over a WAN link using a choice of secure routing protocols including MPLS VPN, L2TPv3, L2VPN, L3VPN, IPSec and routing protocols including OSPF v2/v3, BGPv4, IS-IS, RIP v1/v2, ARP, IP Forwarding, VRRP, Layer 3 Routing and IPv4 / IPv6 features etc.

The VCL “Beyond the Firewall” cyber-security solutions are designed to assist organizations to detect, prevent and secure their network against firewall breaches, cyber-attacks, ransomware-attacks, DoS attacks, conduct forensic analysis and trace the attack route in real-time. Most network administrators rely solely on a “Firewall” to secure their IP networks.

VCL-MX-XW, Industrial Grade Ethernet, IEC 61850-3 complied Sub-Station Hardened Switch, is a flexible Ethernet Switch that is packaged in a 1U high, 19-inch rack-mountable shelf that can be installed in harsh environments. It requires no external fans or forced air cooling. This IEC 61850-3 complied switch offers a wide choice of 1+1 redundant power supply options which include 24V DC, -48V DC, 110-125V DC, 110V AC and 240V AC.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.

VCL offers a wide range of GPS / GNSS Primary Reference Clocks (ITU-T G.811) and SSU (Synchronization Supply Unit), a 1+1 fully redundant architecture. Applications include synchronization for Utilities including Power Generation / Distribution / Transmission, Railways / Metro, Airports (including Air-Traffic Control), 2G, 3G, 4G, 5G mobile telecommunications networks, Micro Cell sites and backhaul wireline SDH / SONET and Synchronous Ethernet networks.

Valiant offers next generation STM-1 (optical and electrical), STM-4, STM-16, STM-64 with MPLS-TP SDH multiplexers and SONET Multiplexer with MPLS-TP, T1, T3/DS3, OC-3, OC-12, OC-48, OC-192, FE/GE/10GE to provide multiple services. The SDH / SONET Multiplexer with MPLS-TP is a compact, modular, and cost effective multiplexer equipment designed to manage bandwidth and provide E1/T1, E3/DS3, FE/GE/10GE interfaces.

Valiant offers 8/16 E1/T1 Links (24/48 E1/T1 Ports), 1+1 Automatic Protection / AB Fallback Switching Equipment: This equipment is to be used when the customer wants to use two different E1/T1 links of the network to establish a 1+1 redundant path to ensure continued E1/T1 service between two points even if one of the network E1/T1 link fails.

VCL IP/MPLS Router is a family of intelligent MPLS (Multiprotocol Label Switching) Routers which can be used to securely inter-connect multiple LAN networks over a WAN link using a choice of secure routing protocols including MPLS VPN, L2TPv3, L2VPN, L3VPN, IPSec and routing protocols including OSPF v2/v3, BGPv4, IS-IS, RIP v1/v2, ARP, IP Forwarding, VRRP, Layer 3 Routing and IPv4 / IPv6 features etc.

The VCL “Beyond the Firewall” cyber-security solutions are designed to assist organizations to detect, prevent and secure their network against firewall breaches, cyber-attacks, ransomware-attacks, DoS attacks, conduct forensic analysis and trace the attack route in real-time. Most network administrators rely solely on a “Firewall” to secure their IP networks.

VCL offers a wide range of GPS / GNSS Primary Reference Clocks (ITU-T G.811) and SSU (Synchronization Supply Unit), a 1+1 fully redundant architecture. Applications include synchronization for Utilities including Power Generation / Distribution / Transmission, Railways / Metro, Airports (including Air-Traffic Control), 2G, 3G, 4G, 5G mobile telecommunications networks, Micro Cell sites and backhaul wireline SDH / SONET and Synchronous Ethernet networks.

VCL-SafeComm-E is a family of Ethernet Failover Protection Switches that provide 1+1 Automatic Ethernet Failover / AB Fallback Protection between an "active” and "standby" equipment; or between “main” and “standby” networks which are connected to the network through an Ethernet interface.