E1 Failover (E1 Automatic Protection) Switch

VCL Products > Automatic Protection Switch > E1 Failover Switch

E1 Failover (E1 Automatic Protection) Switch

Get Data Sheet

Valiant's E1 Fail-Over (E1 Protection) Switch (12 E1 Ports - 4 Links) allows the user to connect a single E1 line from the telephone company to an "active", as well as to a "standby" E1 terminal, such as data server / router etc. at the customer premises.

How it works ? - In the event of the failure of the data server / router connected to the "A / active" port of the E1 Protection (Fail-Over) Switch, it shall automatically switch and connect the E1 line from the telephone company to the data server / router on the "B / standby" port. This ensures minimum downtime - which would have otherwise occurred due to equipment failure connected to the "A / active" port. This equipment may be used to enhance the reliability and the efficiency of the customer's data network.

E1 Protection Fail-Over Switch 12 E1 Ports 4 Links

Features & Highlights

Allows the user to connect an E1 line from the Telephone Company and to switch it automatically between an "active" and a "standby" E1 terminal at the customer premises. The user programmable switching criterion may be Loss Of E1 Signal, AIS and Loss Of E1 Frame.
Can accommodate upto four E1 lines - may be used switch between "active" and "standby" E1 terminals connected to upto four (or fewer) E1 lines.
Independent switching for each of the four E1 lines.
User programmable switching criterion - independent for each E1 line.
Built-in real-time clock / real-time logging maintains a history of all events.
Remotely accessible over a TCP-IP networks. Allows the user to access and carry out maintenance, or / and switch the E1 line(s) between the "active" and "standby" E1 terminals, remotely, if required.
Allows the users to install and maintain active/standby/duplicate customer premises data networks/data servers, without bearing the recurring $$ expense of leasing additional expensive E1 lines from the telephone company.
Automatically switches the E1 line from the Telephone Company between the "active" and "standby" E1 equipment at the customer premises, according to the customer-programmed criterion.
Improves equipment and data security.
Allows the user to co-locate the "backup / standby" equipment in a different room/building and prevent any data loss arising out of conditions of natural calamity such as fire, flooding etc.
Increases the reliability of the customer's data/IT networks without having to bear the recurring and additional cost of leasing additional E1 lines from the telephone company. The equipment may be used to create secondary/backup systems at the customer premises to provide virtually uninterrupted service..

Application Note

The E1 Fail-Over Switch should be used when the customer is using a E1 line to connect to and install "active" E1 equipment and "standby" E1 equipment (such as a ROUTER or a PBX) at the customers premises.
The E1 Failover Switch shall automatically switch the E1 line from the telephone company between the ACTIVE E1 data server / router and the STANDBY E1 data server / router. Should the ACTIVE E1 data server / router fail or be removed from service, the E1 line from the telephone company automatically switches to the STANDBY E1 data server / router without requiring any customer or user intervention.
8/16 E1/T1 Links (24/48 E1/T1 Ports), 1+1 Automatic Protection Switching Equipment: This equipment is to be used when the customer wants to use two different E1/T1 links of the network to establish a 1+1 redundant path to ensure continued E1/T1 service bewteen two points even if one of the network E1/T1 link fails.

Example - The customer may want to use E1/T1 Optical Fiber and an E1/T1 Radio link and to provide an ACTIVE and a STANDBY link between a BSC and a BTS so that when the E1/T1 Optical Fiber (ACTIVE) link goes down the STANBY / REDUNDANT E1/T1 Radio link automatically gets connected to provide continued connectivity and service between the BSC and the BTS.

Network Interface

Number of Interfaces	4 Telco E1 Links (common link/Telco T1s) 4 Active E1 Links (for Equipment-A) 4 Standby E1 Links (for Equipment-B)
Line Rate	E1 - 2.048 Mbps
Line Code	HDB3
Frame Structure	As per ITU-T G.704 / or Un-Framed E1 (User Selectable)
Bit Rate	2048 Kbps ± 50 ppm
Jitter Tolerance	As per ITU-T G.823
Output Jitter	< 0.05 UI (in the frequency range of 20 Hz to 100 KHz)
Nominal Line Impedance	120 Ohms Balanced RJ-45
Nominal Pulse Width	244 ns
Pulse Mask	As per ITU (CCITT) Rec. G.703
Loss and recovery of frame alignment	As per clause 3 of ITU (CCITT) G.732
Loss and recovery of multiframe alignment	As per clause 5.2 of ITU (CCITT) G.732

AC Power Supply Specifications

Output voltage of AC Adapter	100 - 240V AC
Range of input AC voltage	100 V to 240 V AC, 50Hz / 60Hz.
System Input voltage	7.5 V DC to 9.0 V DC with DC input polarity protection.
Maximum full load output current	2.5 A at 7.5 V DC/9.0 V DC
Input voltage reversal protection	Provided in the Card
Efficiency at full load	>86%

Management and Monitoring

RS232 serial, USB serial interfaces for local terminal access.
10/100BaseT Ethernet Interface for remote access over an IP network.
Encrypted Password Protection.
Telnet – Remote access over IP links.
SSH – Secured remote access using Secure Shell Protocol over IP links.
SNMP Traps and NMS for real time remote monitoring and management over an IP network.
Automatic Link Test feature link testing at user programmable periodical intervals.
Visual I/O status LED Display.

Operations and Maintenance (OAM) Interfaces

RS232 serial interface for local terminal access
USB serial interfaces for local terminal access
10/100BaseT Ethernet Interface for remote access over an IP network.

NMS (with Telnet) XPort Specifications

Network Interface	RJ-45 Ethernet 10BaseT or 100BaseT-TX (auto sensing)
Compatibility	Ethernet Version 2.0 IEEE802.3
Protocols Supported	ARP, UDP/IP, TCP/IP, Telnet, ICMP, SNMP, DHCP, BOOTP, TFTP, Auto IP, SMTP and HTTP
LEDs	10Base-T and 100Base-TX Activity, full/half duplex
Management	Internal web server, SNMP (read only), Serial login, Telnet login

EMI Compliance

Radiated and conducted emissions - complies with Class B limits of EN55022:1998
Direct and Indirect ESD - complies with EN55024:1998
RF Electromagnetic Field Immunity - complies with EN55024:1998
Electrical Fast Transient/Burst Immunity - complies with EN55024:1998
Power Frequency Magnetic Field Immunity - complies with EN55024:1998
RF Common Mode Conducted Susceptibility - complies with EN55024:1998

Mechanical Specifications

Rack mounting : Standard 19-Inch. DIN Rack
H x D x W : 44 x 260 x 477 mm.
Weight : 4.00 kg.

Command Language

Command Line Interface (English text commands)

Management Ports (COM Port)

Serial Port: 9.6Kbps (Async). ASCII/VT100/HyperTerminal
10BaseT Ethernet: Telnet

Temperature

Operating : 0°C to 50°C
Humidity : 5% to 95% Non-Condensing

Compliance / Regulatory

EMC FCC Part 15 Class 2
Operation ETS 300 019 Class 3.2
Storage ETS 300 019 Class 1.2
Transportation ETS 300 019 Class 2.3

Application #1: Telco E1 Link Connected to Equipment - A

User programmable criterion for switching between Active and Standby E1 Links at the customers premises.

Application #3: Equipment - A recovers - Telco E1 automatically switches to Equipment - A

Application #2: Equipment - A Fails - Telco E1 automatically switches to Equipment - B

Other Related Products:
8 E1 Links (24 E1 Ports) Protection / AB Fallback Switching 16 E1 Links (48 E1 Ports) Protection / AB Fallback Switching 8 T1 Links (24 T1 Ports) Protection / AB Fallback Switching 16 T1 Links (48 T1 Ports) Protection / AB Fallback Switching T1 Failover (Protection) Switch DS3 Failover (Protection) Switch E3 Failover (Protection) Switch 1+1 Ethernet Failover / AB Fallback Switch

Valiant Communications is an ISO 9001:2015, ISO 10001:2018, ISO 14001:2015, ISO 27001:2013 and ISO 45001:2018 certified equipment manufacturer.

Automatic Protection SwithingE1 Failover Switch

VCL Products > Automatic Protection Switch > E1 Failover Switch

Features & Highlights

Application Note

Network Interface

AC Power Supply Specifications

Management and Monitoring

Operations and Maintenance (OAM) Interfaces

NMS (with Telnet) XPort Specifications

EMI Compliance

Mechanical Specifications

Command Language

Management Ports (COM Port)

Temperature

Compliance / Regulatory

Application #1: Telco E1 Link Connected to Equipment - A

Application #3: Equipment - A recovers - Telco E1 automatically switches to Equipment - A

Application #2: Equipment - A Fails - Telco E1 automatically switches to Equipment - B

Links

Products

Products

Products

Automatic Protection Swithing
E1 Failover Switch