Modes of Operation

There are three modes in which the VCL-SafeComm T1, 1+1 Automatic Protection / AB Fallback Switch can be configured to operate in:

• AUTOMATIC SWITCHING MODE
• EXTERNAL TRIGGER SWITCHING MODE
• MANUAL SWITCHING MODE

AUTOMATIC SWITCHING MODE:

• The VCL-SafeComm T1, 1+1 Automatic Protection / AB Fallback Switch can be configured to operate in an AUTOMATIC SWITCHING MODE. In the automatic mode, the switch shall automatically switch and re-route the T1 circuits from the MAIN route to the STANDBY route if there is an AIS or a LOS (LOSS OF SIGNAL) alarm, on the MAIN T1 link route.
• Similarly, in the automatic mode the switch shall automatically switch back and re-route the T1 circuits from the STANDBY route to the MAIN route upon the restoration of the service on the MAIN T1 link route.
• All switching parameters and link restoration parameters are user programmable.

EXTERNAL TRIGGER SWITCHING MODE:

• Sometimes the user wants to switch the T1 circuits between the MAIN route and the STANDBY route when some external event occurs. In the EXTERNAL TRIGGER MODE the user can switch between the MAIN T1 route and the STANDBY T1 route when an external trigger (such as an closed/opened physical contact) is applied to the switch. This feature was added to make it compatible with certain radios equipment suppliers, where they apply an external trigger to switch and re-route the T1 circuits between their main T1 radios and standby T1 radios.

MANUAL SWITCHING MODE:

• In Manual Switching Mode, the user shall use manual Telnet commands to switch the E1 circuits between the MAIN route and the STANDBY route, manually, using Telnet commands. In this mode the AUTOMATIC MODE and the EXTERNALL TRIGGER MODE are both disabled and the manual commands over ride all other modes.

Product Application Note: 8/16 E1/T1 Links (24/48 E1/T1 Ports), 1+1 Automatic Protection / AB Fallback Switching Equipment: This equipment is to be used when the customer wants to use two different E1/T1 links of the network to establish a 1+1 redundant path to ensure continued E1/T1 service bewteen two points even if one of the network E1/T1 link fails. Example - the customer may want to use E1/T1 Optical Fiber and an E1/T1 Radio link and to provide an ACTIVE and a STANDBY link between a BSC and a BTS so that when the E1/T1 Optical Fiber (ACTIVE) link goes down the STANBY / REDUNDANT E1/T1 Radio link automatically gets connected to provide continued connectivity and service between the BSC and the BTS.

Product Application Note: The E1/T1 Fail-Over Switch should be used when the customer is using a single E1/T1 link to provide protection equipment to the customers premises by using one E1/T1 ACTIVE and one E1/T1 STANDBY equipment (such as a ROUTER or a PBX). The E1/T1 Failover Switch shall automatically switch the E1/T1 that is being received from the telephone company between the ACTIVE E1/T1 equipment and the STANDBY E1/T1 equipment. Should the ACTIVE E1/T1 equipment go bad or be removed from service, the E1/T1 link from the telephone company automatically gets switched to the STANDBY E1/T1 equipment without any customer or user intervention.

T1 Interface

Clock

• Transparent between the two points of the T1 Links.

Management and Control

• Serial Management Port (RS232) - COM Port
• 10/100 BaseT for Remote Management over a LAN
• 10/100 BaseT Telnet over a TCP-IP Network

Specification and Regulation Compliance

• Meets CE requirements
• Complies with FCC, Part 68 and Part 15 subpart A specifications
• Safety - UL 1459 Issue 2

Command Language

• Command Line Interface (English text commands)

Alarm Contact Closures

• 1 Alarm Relay
• Type - Form "C" relay

Temperature

• Operating 0°C to 50°C
• Humidity 5% to 95% non-condens

Dimensions and Weight

AC Power Supply Specifications

DC Power Supply Specifications

Application Diagrams # 1

Features

• 1+1 Link Protection
• Radio + Fiber Media Protections
• Under 50ms switch over time
• Continous T1 Link Status Monitoring
• Designed for disaster recovery and Mission critical applications

Point-to-Point Application: May be used in a point-to-point configuration to provide 1+1 protected / Alternate Routing Path between any two point, using diverse (or similar) T1 transmission mediums.

Application Diagrams # 2